Professional heating, cooling & air quality services serving Redmond and surrounding communities in Washington. NATE-certified, 24/7 emergency response.
NATE-certified technicians providing the complete range of heating and cooling services.
When your AC blows warm air, short cycles, or fails to start, the problem may involve a failed compressor, low refrigerant charge, frozen evaporator coil, or faulty control board. Professional repair identifies the exact fault and restores rated SEER efficiency through precise, manufacturer-guided procedures.
Leaking and disconnected ductwork wastes up to 30 percent of conditioned air before it reaches living spaces, forcing your HVAC system to work harder and driving up energy costs. Professional duct repair seals joints, replaces damaged sections, and restores proper static pressure balance.
A comprehensive furnace tune-up includes combustion analysis, heat exchanger inspection, and verification of gas pressure at the manifold. Technicians clean burners, test flame sensor microamp readings, and confirm proper flue draft to maintain safe, efficient operation throughout the heating season.
A professional HVAC inspection evaluates the complete system from furnace combustion and heat exchanger integrity to air conditioning refrigerant charge and electrical safety. Technicians document equipment age, efficiency ratings, and any code violations to give you a clear picture of system health.
When your heat pump struggles to maintain temperature or runs continuously without reaching setpoint, the problem often traces to refrigerant leaks, failing capacitors, or degraded reversing valves. Skilled technicians restore rated HSPF and SEER performance through systematic component-level troubleshooting.
An annual air conditioning tune-up catches refrigerant leaks, worn contactor points, and degraded fan motors before they cascade into compressor damage. Technicians measure temperature differential across the coil, verify amp draws, and confirm proper subcooling to protect your investment.
Ductless mini-split systems require specialized diagnostics for inverter-driven compressors, electronic expansion valves, and multi-zone communication boards. Our technicians resolve issues including refrigerant leaks at flare connections, blinking error codes, frozen evaporator coils, and failing fan motors.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
Upgrading to a modern heat pump delivers dual-mode heating and cooling from a single system, with top-tier models achieving 10+ HSPF and 20+ SEER2 ratings. Proper installation includes Manual J load calculations, refrigerant line sizing, and electrical panel verification for reliable year-round comfort.
Maintaining safe and efficient boiler operation requires precise attention to water chemistry, flue gas temperatures, and combustion efficiency. Professional repair addresses leaking heat exchangers, malfunctioning aquastats, air-bound radiators, and ignition system failures to restore rated AFUE output.
A dryer that takes multiple cycles to dry clothes or feels excessively hot to the touch signals a restricted vent line. Technicians clear lint accumulation using rotary brush systems and compressed air, then verify exhaust velocity meets manufacturer specifications for safe, efficient operation.
Indoor air quality suffers when ductwork harbors years of accumulated particulate matter, allergens, and biological growth. Thorough duct cleaning addresses every branch run, main trunk line, and register boot using agitation tools and high-powered vacuum extraction to restore clean airflow.
Replacing an aging HVAC system with properly sized, high-efficiency equipment can reduce energy costs by 30 to 50 percent. Professional installation covers equipment selection, ductwork modifications, refrigerant line installation, electrical upgrades, and thorough commissioning to verify rated SEER and AFUE output.
Professional smart thermostat installation goes beyond mounting and Wi-Fi pairing. Technicians verify your system has the necessary common wire, confirm compatibility with multi-stage heating and cooling equipment, and program setpoints and schedules tailored to your household for immediate energy savings.
HVAC emergencies do not follow business hours, and a failed system in extreme temperatures puts your household at risk. Our technicians carry common replacement parts including capacitors, contactors, ignitors, and fan motors to resolve most failures in a single visit and restore comfort fast.
With 86,605 residents relying on dependable heating and cooling, Redmond needs HVAC contractors who can deliver at scale without losing the personal touch. KIC Refrigeration has built our reputation in the Redmond market by treating every project — from a thermostat installation to a full system replacement — with the same load calculation precision and installation quality.
Our Redmond, WA teams know the HVAC landscape inside and out. We understand which neighborhoods have aging furnaces approaching end of life, where duct systems are undersized, and which equipment performs best across the Washington climate. That local intelligence means better equipment recommendations and longer-lasting comfort for our customers.
Built on NATE certification, transparent pricing, and a guarantee that we stand behind.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
We help you select equipment with the highest SEER2, HSPF2, and AFUE ratings that fit your budget, and we install it to manufacturer specifications so you actually achieve rated efficiency. Proper charge, proper airflow, proper duct sealing — the details that turn rated efficiency into real savings.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
HVAC failures do not wait for business hours and neither do we. Our emergency technicians are dispatched around the clock — nights, weekends, and holidays — so you never go without heat in winter or cooling in the peak of summer.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
Common questions about HVAC service, costs, and what to expect when you call.
The ideal time for HVAC replacement in Redmond is during the shoulder seasons — spring and fall — when demand is lower, equipment availability is highest, and scheduling is more flexible. Contractors are less booked during these periods, which means faster installation timelines and potentially more competitive pricing. You are also more likely to find manufacturer rebates, utility incentive programs, and promotional financing during off-peak months. From a technical standpoint, moderate temperatures allow your new system to be commissioned and tested under less extreme conditions. However, KIC Refrigeration completes HVAC installations year-round in Washington and can often start within days of your approved estimate, even during peak summer or winter demand. If your current system is showing signs of failure, do not wait for the perfect season — a planned replacement is always better than an emergency one.
As a guideline for Redmond homeowners, consider replacement when your system is 15 to 20 years old, when the repair cost exceeds 50 percent of a new system, when the equipment uses R-22 refrigerant which is no longer manufactured and costs $100 or more per pound, or when your system runs constantly without adequately heating or cooling your home. Additional indicators include frequent breakdowns — more than two per heating or cooling season — rising utility bills despite regular maintenance, uneven temperatures between rooms, and excessive noise or dust. The age thresholds vary by equipment type: air conditioners and heat pumps typically last 15 to 20 years, furnaces 20 to 25 years, and boilers 25 to 30 years. KIC Refrigeration provides honest repair-versus-replace assessments at every service call, including side-by-side cost projections for both options.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most Washington locations. For Redmond homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
A comprehensive HVAC inspection from KIC Refrigeration in Redmond covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
Absolutely. Modern high-efficiency HVAC equipment can reduce heating and cooling costs by 20 to 40 percent compared to systems installed 15 or more years ago. The improvement comes from advances in compressor technology, variable-speed motors, and smarter controls. In Redmond, upgrading from a 10-SEER air conditioner to a 16-SEER2 or higher unit delivers substantial monthly savings — the higher the SEER2 rating, the less electricity consumed per BTU of cooling. On the heating side, replacing an 80-percent AFUE furnace with a 96-percent modulating furnace means that 16 cents of every heating dollar previously wasted up the flue now heats your home. Heat pumps offer even greater efficiency, delivering 2 to 4 times more heating energy than they consume in electricity. KIC Refrigeration calculates projected energy savings for any equipment upgrade so you can see the return on investment before making a decision.
Yes. The EPA estimates that Energy Star certified smart thermostats save Redmond homeowners an average of 8 percent on heating and cooling costs annually, which translates to $50 to $150 per year for a typical household. Models from Ecobee, Nest, and Honeywell Home use occupancy sensors, geofencing, and learning algorithms to build a schedule around your actual habits, automatically lowering temperatures when you leave and restoring comfort before you return. Many smart thermostats also provide energy usage reports, filter change reminders, and maintenance alerts that help you keep your system running efficiently. Some Washington utility providers offer rebates of $50 to $100 on qualifying smart thermostat purchases, further reducing the cost. KIC Refrigeration installs and configures smart thermostats to communicate properly with your specific HVAC system — including multi-stage equipment and heat pumps that require specialized wiring.
Our reputation is built on honest service, skilled technicians, and systems that perform.
"Boiler repair was handled same-day. The tech was knowledgeable and did not try to upsell me on anything I did not need. Refreshing honesty."
"Mini split repair was done right the first time. The outdoor unit had a refrigerant leak and they found it, fixed it, and recharged the system same day."
"Boiler repair took a couple visits because they needed to order a part, but they were upfront about it and the repair has held up perfectly."
Our NATE-certified crews provide HVAC service throughout the surrounding area.